• 7

Operation and Maintenance Manual–Cast Steel Gate Valves

1. General
Valves of this series are used to close or open pipelines in pipeline system so as to maintain normal operation of the system.

2. Product Description
2.1Technique requirement
2.1.1 Design and manufacture: API600、API603、ASME B16.34、BS1414
2.1.2 Connection end dimension:ASME B16.5、ASME B16.47、ASME B16.25
2.1.3 Face to face or end to end:ASME B16.10
2.1.4 Inspection and test:API 598、API600
2.1.5 Nominal sizes:MPS2″~48″,Nominal class ratings:Class150~2500
2.2 Valves of this series are manual (actuated through handwheel or gear box) gate valves with flange ends and butt welding end .The valve stem moves vertically. When turn the handwheel clockwise, the gate falls down to close the pipeline; when turn the handwheel counterclockwise, the gate rises up to open pipeline.
2.3 The structural see Fig.1, 2and3.

fqwasda

2.4 Names and materials of main parts are listed in Table 1.

Part Name Material
Body and bonnet ASTM A216 WCBASTM A352 LCBASTM A217 WC6
ASTM A217 WC9ASTM A351 CF3ASTM A351 CF3M
ASTM A351 CF8ASTM A351 CF8MASTM A351 CN7M
ASTM A494 CW-2MMonel
gate ASTM A216 WCBASTM A352 LCBASTM A217 WC6
ASTM A217 WC9ASTM A351 CF3ASTM A351 CF3M
ASTM A351 CF8ASTM A351 CF8MASTM A351 CN7M
ASTM A494 CW-2MMonel
seat ASTM A105ASTM A350 LF2F11F22
ASTM A182 F304304L)、ASTM A182 F316316L
ASTM B462Has.C-4Monel
stem ASTM A182 F6aASTM A182 F304304L
ASTM A182 F316316L)、ASTM B462Has.C-4Monel
Packing Braided graphite and flexible graphitePTFE
Stud/nut ASTM A193 B7/A194 2HASTM L320 L7/A194 4
ASTM A193 B16/A194 4ASTM A193 B8/A194 8
ASTM A193 B8M/A194 8M
Gasket 304316+Graph304316)、Has.C-4
MonelB462
Seat ring/Disc/surfaces 13Cr18Cr-8Ni18Cr-8Ni-MoNiCu alloy25Cr-20NiSTL

3. Storage, maintenance, Installation and operation

3.1 Storage and maintenance
3.1.1 The valves should be stored in dry and well ventilated room. The passage ends should be plugged with covers.
3.1.2 The valves under long-time storage should be examined and cleaned regularly, especially the cleaning of seating face to prevent damage, and the finished surfaces should be coated with rust inhibiting oil.
3.1.3 If storage period exceeds 18 months, the valves should be tested and records should be made.
3.1.4 Installed valves should be examined and repaired regularly. The main maintenance points include the following:
1)Sealing face
2)Valve stem and valve stem nut.
3)Packing.
4)Fouling on internal surface of valve body and valve bonnet
3.2 Installation
Before installation, make sure valve identification (such as model, DN, 3.2.1PN and material) are marked according to requirements of pipeline system.
3.2.2 Before installation, carefully check valve passage and sealing face. If there is any dirt, clean it thoroughly.
3.2.3 Before installation, make sure all bolts are fastened tightly.
3.2.4 Before installation, make sure packing is compressed tightly. However, the motion of valve stem should not be disturbed.
3.2.5 The installation place of the valve should facilitate inspection and operation. The preferable position should be that the pipeline is horizontal, handwheel is above, and valve stem is vertical.
3.2.6 For normally closed valve, it is not suitable to install it in the place where working pressure is very big to avoid damage of valve stem.
3.2.7 Socket welded valves shall at least meet the following requirements when they are welded for installation in pipeline system on site:
1) Welding should be carried out by the welder who possesses welder’s qualification certificate approved by the State Boiler and Pressure Vessel Authority; or the welder who has obtained welder’s qualification certificate specified in ASME Vol.Ⅸ.
2) Welding process parameters must be selected as specified in the quality assurance manual of welding material.
3) The chemical composition, mechanical performance and corrosion resistance of the filler metal of welding seam should be compatible with base metal.
3.2.8 The valve is normally installed, big stress due to supports, accessories and pipes should be avoided.
3.2.9 After installation, during pressure testing of pipeline system, the valve must be fully opened.
3.2.10 Bearing point: if the pipeline has sufficient strength to bear valve weight and operation torque, then no bearing point is required, otherwise valve should have bearing point.
3.2.11 Lifting: don’t use handwheel to hoist and lift valve.
3.3 Operation and use
3.3.1 During service period, valve gate must be fully opened or fully closed to avoid surface damage of seat ring and valve gate due to high-speed medium. It cannot be used to adjust flow capacity.
3.3.2 When open or close the valve, use handwheel instead of auxiliary lever or use other tool.
3.3.3 At working temperature, make sure instantaneous pressure be lower than 1.1times that working pressure of pressure-temperature ratings in ASME B16.34.
3.3.4 Safety relief equipment should be installed on the pipeline to prevent the working pressure of the valve at working temperature from exceeding the maximum allowable pressure.
3.3.5 Stroking and shocking the valve is prohibited during transport, installation and operation period.
3.3.6 Decomposition of unsteady fluid, for example, the decomposition of some fluids can cause volume expansion and lead to working pressure rise, thus damaging the valve and causing permeation, therefore, use appropriate measuring instruments to eliminate or limit factors that may cause decomposition of fluid.
3.3.7 If the fluid is a condensate, this will affect valve performance, use appropriate measuring instruments to reduce temperature of the fluid (for example, to guarantee appropriate temperature of the fluid) or replace it with other type of valve.
3.3.8 For self-inflammable fluid, use appropriate measuring instruments to guarantee ambient and working pressure do not exceed its auto-ignition point (especially notice sunshine or external fire).
3.3.9 In case of dangerous fluid, such as explosive, inflammable. Toxic, oxidation products, it is prohibited to replace packing under pressure (although the valve has such a function).
3.3.10 Make sure the fluid is not dirty, which affects valve performance, does not contain hard solids, otherwise appropriate measuring instruments should be used to remove the dirt and hard solids, or replace it with other type of valve.

3.3.11 Allowable working temperature: 

Material

temperature

Material

temperature

ASTM A216 WCB

-29425℃

ASTM A217 WC6

-29538℃

ASTM A352 LCB

-46343℃

ASTM A217 WC9

--29570℃

ASTM A351 CF3CF3M

-196454℃

ASTM

A494 CW-2M

-29450℃

ASTM A351 CF8CF8M

-196454℃

Monel

-29425℃

ASTM A351 CN7M

-29450℃

-

3.3.12 Make sure the material of valve body is suitable for use in corrosion resistant and rust prevention fluid environment.
3.3.13 During service period, examine sealing performance as per the table below:

Inspection point

Leak

Connection between valve body and bonnet

Zero

Packing seal

Zero

Valve seat

As per technical specification

3.3.14 Regularly check for the wear of sealing face. Packing aging and damage. Make repair or replacement in time if evidence is found.

3.3.15 After repair, re-assemble and adjust the valve, the test tightness performance and make record.

3.3.16 Examination and repair internal is two years.

4. Possible problems, causes and remedial measures

Problem description

Possible cause

Remedial measures

Leak at packing

Insufficiently compressed packing

Re-tighten packing nut

Inadequate quantity of packing

Add more packing

Damaged packing due to long-time service or improper protection

Replace packing

Leak on valve seating face

Dirty seating face

Remove dirt

Worn seating face

Repair it or replace seat ring or valve gate

Damaged seating face due to hard solids

Remove hard solids in the fluid, repair or replace seat ring or valve gate, or replace with other type of valve

Leak at connection between valve body and valve bonnet

Bolts are not properly fastened

Uniformly fasten bolts

Damaged seating surface of valve body and valve bonnet  flange

Repair it

Damaged or broken gasket

Replace gasket

Difficult rotation of handwheel or valve gate cannot be opened or closed

Too tightly fastened packing

Appropriately loosen packing nut

Deformation or bending of sealing gland

Adjust sealing gland

Damaged valve stem nut

Correct thread and remove the dirt

Worn or broken valve stem nut thread

Replace valve stem nut

Bent valve stem

Replace valve stem

Dirty guide surface of valve gate or valve body

Remove dirt on guide surface

Note: Service person should have relevant knowledge and experience with valves.

5. Warranty
After the valve is put into use, the warranty period of valve is 12 months, but does not exceed 24 months after delivery date. During warranty period, the manufacturer will provide repair service or spare parts free of charge for the damage due to material, workmanship or damage provided that operation is correct.


Post time: May-19-2022
Leave Your Message